Chauvet Work Light 15090388 User Manual

User Manual  
 
1. BEFORE YOU BEGIN  
·
·
·
·
·
1 x MotionDrape™ LED  
·
·
·
·
Replacement LEDs  
What Is  
Included  
1 x MotionDrape™ Controller  
1 x Power Cord  
Reusable Zip Ties (Tie Wraps)  
1 x Warranty Card  
1 x Signal Cable  
1 x Quick Reference Guide  
1 x Carrying Bag  
Unpacking Immediately upon receipt, carefully unpack this product and check the container to make  
sure you have received all the parts indicated above in good condition.  
Instructions  
If the container or the material inside the container (this product and any other accessory  
Claims  
included) appears damaged from shipping, or shows signs of mishandling, notify the  
carrier immediately, not CHAUVET®, upon receipt of the damaged merchandise. Failure  
to do so in a timely manner may invalidate your claim with the carrier. In addition, retain  
the container and all the packing material for inspection.  
For other issues such as missing components or parts, damage not related to shipping,  
or concealed damage, file a claim with CHAUVET® within seven (7) days of receiving  
the merchandise.  
Convention  
1~512  
Meaning  
Text  
Conventions  
A range of values  
50/60  
A set of values of which only one can be chosen  
A menu option not to be modified  
Settings  
Menu > Settings A sequence of menu options to be followed  
<ENTER>  
ON  
A key to be pressed on the product’s control panel  
A value to be entered or selected  
Icon  
Meaning  
Icons  
This paragraph contains critical installation, configuration, or  
operation information. Failure to comply with this information may  
render the product partially or completely inoperative, cause  
damage to the product, or cause harm to the user.  
This paragraph contains important installation or configuration  
information. Failure to comply with this information may prevent  
the product from functioning correctly.  
This paragraph reminds you of useful, although not critical,  
information.  
The information and specifications contained in this document are subject to change  
without notice. CHAUVET® assumes no responsibility or liability for any errors or  
omissions that may appear in this manual. CHAUVET® reserves the right to update the  
existing document or to create a new document to correct any errors or omissions.  
Document  
Information  
You can download the latest version of this document from www.chauvetlighting.com.  
© Copyright 2012 CHAUVET®. All rights reserved.  
Electronically published by CHAUVET® in the United States of America.  
Author  
Date  
Editor  
Date  
A. Diaz  
2/13/12  
S. Graham  
2/13/12  
MotionDrape™ LED User Manual (Rev. 05)  
 
Page 3 of 13  
Use on Dimmer  
Outdoor Use  
Sound Activated  
DMX  
Auto Programs  
x
x
P
P
P
Product at a  
Glance  
Auto-ranging Power Supply  
Replaceable Fuse  
User Serviceable  
Duty Cycle  
P
x
x
P
P
Master/Slave  
Please read the following Safety Notes carefully before working with this product. They  
include important safety information about its installation, usage, and maintenance.  
Safety Notes  
·
·
Always connect this product to a grounded circuit to avoid the risk of electrocution.  
Always disconnect this product from the power source before cleaning it or replacing  
the fuse.  
·
·
·
·
·
Avoid direct eye exposure to the light source while the product is on.  
Make sure the power cord is not crimped or damaged.  
Never disconnect this product from power cord by pulling or tugging on the cord.  
Make sure there are no flammable materials close to the unit while operating.  
Do not touch this product’s housing when operating because it may be very hot.  
·
·
·
Always make sure that the voltage of the outlet to which you are connecting this  
product is within the range stated on the decal or rear panel of the product.  
This product is for indoor use only! (IP20) To prevent risk of fire or shock, do not  
expose this product to rain or moisture.  
Always install this product in a location with adequate ventilation, at least 20 in (50  
cm) from adjacent surfaces.  
·
·
·
·
·
Be sure that no ventilation slots on the unit’s housing are blocked.  
Never connect this product to a dimmer.  
Make sure to replace the fuse with another of the same type and rating.  
Never carry this product from the power cord or any moving part.  
The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this  
product at higher temperatures.  
·
·
In the event of a serious operating problem, stop using the unit immediately.  
Never try to repair this product. Repairs carried out by unskilled people can lead to  
damage or malfunction. Please contact the nearest authorized technical assistance  
center.  
·
·
This product is NFPA-certified fire retardant material.  
Keep this User Manual for future consultation. If you sell this product to another user,  
be sure that they also receive this document.  
Page 4 of 13  
MotionDrape™ LED User Manual (Rev. 05)  
 
2. INTRODUCTION  
Product Overview  
Front Panel  
Button Menu  
LED Display  
Top Panel  
Curtain Input  
Power In  
Fuse holder  
DMX Out  
On/Off Switch  
DMX In  
Product Dimensions  
MotionDrape™ LED User Manual (Rev. 05)  
Page 5 of 13  
 
3. SETUP  
This product has an auto-ranging power supply and can work with an input voltage  
range of 100~240 VAC, 50/60 Hz.  
AC Power  
To determine the power requirements for this product (circuit breaker, power outlet, and  
wiring), use the current value listed on the label affixed to the product’s back panel, or  
refer to the product’s specifications chart. The listed current rating indicates the  
product’s average current draw under normal conditions.  
Always connect this product to a protected circuit (circuit breaker or fuse),  
making sure that it has an appropriate electrical ground to avoid the risk of  
electrocution or fire.  
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even  
if the rheostat or dimmer channel serves only as a 0 to 100% switch.  
Fuse  
Replacement  
Follow the instructions below to change the fuse, if necessary.  
Disconnect this product from the power outlet before replacing the fuse.  
1. Wedge the tip of a flat head screwdriver into the slot of the fuse holder and pry out of  
its housing.  
2. Remove the blown fuse from its holder and replace with a fuse of the exact same  
type and rating.  
3. Insert the fuse holder back into place, and reconnect power.  
Installed fuse  
(held by plastic clip)  
Safety cap  
Spare fuse holder  
(inside safety cap)  
This product ships with no spare fuse. The safety cap does have room for a spare.  
Always replace a blown fuse of the same type and rating.  
Page 6 of 13  
MotionDrape™ LED User Manual (Rev. 05)  
 
Before mounting this product, read and follow the safety recommendations indicated in  
the Safety Notes section (page 2 of this manual).  
Mounting  
Orientation  
Rigging  
The MotionDrape™ LED may be mounted in any position; however, make sure  
adequate ventilation is provided around the product.  
Before deciding on a location for this product, always make sure that it will be easy to  
access the unit for maintenance and programming purposes.  
Make sure that the structure onto which you are mounting this product can support its  
weight. Please see the Technical Specifications section of this manual for weight  
information.  
Mount the product securely to a rigging point, whether an elevated platform or a truss.  
Reusable zip ties (tie wraps) are provided with the MotionDrape™ LED for quick and  
easy mounting.  
This product can be used with the CHAUVET® CH-31 portable truss or any similar  
portable trussing system.  
Grommets for easy truss  
mounting and various  
stand applications  
Mounting Diagram  
MotionDrape™ LED User Manual (Rev. 05)  
 
Page 7 of 13  
4. OPERATION  
To access the control panel functions, use the four buttons located underneath the  
display. Please refer to the Product Overview (page 5) to see the buttons location on the  
control panel.  
Control Panel  
Operation  
Button  
Function  
Press to find an operation mode or to back out of the current menu  
option  
<MENU>  
<ENTER>  
<UP>  
Press to activate a menu option or a selected value  
Press to scroll up the list of options or to find a higher value  
Press to scroll down the list of options or to find a lower value  
<DOWN>  
Mode  
Programming Steps  
Description  
Menu Map  
Version  
Software Version  
Shows the software version number  
Disables unit’s auto mode function  
Enables unit’s auto mode function  
Disables unit’s sound mode function  
Enables unit’s sound mode function  
Disables unit’s DMX512 mode function  
NO  
YES  
NO  
Automatic  
Sound  
YES  
NO  
DMX Mode  
Speed  
Enables unit’s DMX512 mode and sets  
starting address  
YES  
1~512  
Selects how fast the auto mode program  
runs  
1~9  
Disables numbered program running in  
sequence in auto or sound mode  
NO  
Program  
1~30  
Enables numbered program running in  
sequence in auto or sound mode  
YES  
Set this product in DMX mode to control it with a DMX controller.  
1. Connect this product to a suitable power outlet.  
2. Turn this product on.  
Configuration  
(DMX)  
3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input  
socket of this product.  
When selecting a starting DMX address, always consider the number of DMX channels  
the selected DMX mode uses. If you choose a starting address that is too high, you  
could restrict the access to some of the product’s channels.  
Starting Address  
The MotionDrape™ LED uses up to 8 DMX channels in its 8-channel DMX mode, which  
defines the highest configurable address to 505.  
If you are not familiar with the DMX protocol, you may refer to the DMX Primer section in  
the Technical Information chapter.  
To select the starting address, do the following:  
1. Press <MENU> repeatedly until Dmx512 shows on the display.  
2. Press <ENTER>.  
3. Press <UP> to select Yes in the menu.  
4. Press <ENTER>. Address should appear on the screen.  
5. Use <UP> or <DOWN> to select the starting address.  
6. Press <ENTER>.  
Page 8 of 13  
MotionDrape™ LED User Manual (Rev. 05)  
 
Set this product in one of the standalone modes to control it without a DMX controller.  
1. Connect this product to a suitable power outlet.  
2. Turn this product on.  
Configuration  
(Standalone)  
Never connect a product that is operating in any standalone mode, whether Static,  
Automatic, or Sound to a DMX string connected to a DMX controller. This is  
because products in standalone mode may transmit DMX signals that could  
interfere with the DMX signals from the controller.  
To enable the Sound Active mode, do the following:  
1. Press <MENU> repeatedly until Sound shows on the display.  
2. Press <ENTER>.  
Sound Active  
Mode  
3. Use <UP> or <DOWN> to select Yes.  
4. Press <ENTER>.  
5. Turn the music on until the product responds to the beat of the music.  
The product will only respond to low frequencies of the music (bass and drums).  
To enable the Automatic Mode, follow the instructions below:  
1. Press <MENU> repeatedly until Automatic shows on the display.  
2. Press <ENTER>.  
Automatic Mode  
3. Use <UP> or <DOWN> to select Yes.  
4. Press <ENTER>.  
MotionDrape™ LED User Manual (Rev. 05)  
 
Page 9 of 13  
DMX Channel Assignments and Values  
Channel  
1
Function  
Value  
Setting  
8-CH  
000 ó 007 No function  
008 ó 255 0~100%  
Dimmer  
Strobe  
000 ó 010 No function  
011 ó 255 0~100%  
2
3
4
5
Red  
000 ó 255 0~100%  
Green  
Blue  
000 ó 255 0~100%  
000 ó 255 0~100%  
000 ó 015 No function  
016 ó 031 Falling Star  
032 ó 047 Diagonal Color Bands  
048 ó 063 Color Pattern Chase  
064 ó 079 Inward Arrow (L-R)  
080 ó 095 Color Stack  
096 ó 111 Multi-Color Freeway  
112 ó 127 Color Wave (L-R)  
128 ó 143 Color Wave (R-L)  
144 ó 159 Color Bar Chase (L-R)  
160 ó 175 Color Bar Chase (R-L)  
176 ó 191 Windmill  
6
Programs 1-15  
192 ó 207 Fan  
208 ó 223 Whirlpool  
224 ó 239 Falling Snow  
240 ó 255 Multi Box Frenzy  
000 ó 015 No function  
016 ó 031 Center Burst  
032 ó 047 Outer Burst  
048 ó 063 EQ Effect  
064 ó 079 Rolling Color  
080 ó 095 Horizontal Stacking  
096 ó 111 Inner Zone  
112 ó 127 Outer Zone  
7
Programs 16-30  
128 ó 143 Diamond Spread  
144 ó 159 Single Diamond Squeeze  
160 ó 175 Follow The Leader  
176 ó 191 Crisscross  
192 ó 207 X-Factor  
208 ó 223 Double Diamond Squeeze  
224 ó 239 Red X Factor  
240 ó 255 Multicolor Rain  
000 ó 255 0~100%  
8
Speed  
Page 10 of 13  
MotionDrape™ LED User Manual (Rev. 05)  
 
5. TECHNICAL INFORMATION  
General Troubleshooting  
Symptom  
Possible Cause(s)  
Possible Action(s)  
General low light intensity  
Dirty LEDs  
Clean the MotionDrape™ LED drape regularly  
One LED in an LED group  
failed  
Faulty (shorted) LED  
Replace faulty LED  
Faulty (open) LED  
Replace faulty LED  
All the LEDs in a group  
failed  
Faulty LED cable  
Replace faulty LED cable  
Faulty LED driver  
Replace faulty LED Driver box  
Replace faulty LED Driver box  
Repair or replace faulty cable  
Replace MotionDrape™ LED controller  
Replace MotionDrape™ LED controller  
Faulty LED driver box  
Single MotionDrape™ LED  
controller: All LEDs in a  
drape failed  
Faulty drape output cable  
Faulty MotionDrape™ LED controller  
Faulty MotionDrape™ LED controller  
If using DMX connection, wrong DMX address  
on the corresponding controller  
Set the starting DMX address correctly  
Multiple MotionDrape™ LED If using proprietary serial link, wrong  
controllers: All LEDs on a  
controller failed  
Master/Slave setting on the corresponding  
controller  
Set the starting Master/slave mode correctly  
Check power to the MotionDrape™ LED  
controller  
MotionDrape™ LED controller not powered  
Faulty DMX cable  
Repair or replace faulty cable  
Excessive circuit load  
Check total load placed on the electrical circuit  
Breaker/Fuse keeps blowing  
Check for a short in the electrical wiring (internal  
and/or external)  
Short circuit along the power wires  
No power  
Check for power on Mains  
MotionDrape™ LED  
controller does not power  
up  
Faulty or lose power cord  
Faulty internal power supply  
Wrong DMX addressing  
Wrong polarity on the controller  
Lose or damaged cables  
Faulty Main PCB  
Check power cord  
Replace internal power supply  
Check DMX controller and product addressing  
Check polarity switch settings on the controller  
Check DMX and signal patch cables  
Replace Display PCB  
Product is not responding to  
DMX  
Non compatible signal patch cables  
Bouncing signals  
Use only compatible cables  
Install terminator as suggested  
Do not exceed maximum recommended length  
Loss of signal on some  
MotionDrape™ LED  
controllers  
Long cable / Low level signal  
Install an optically coupled DMX splitter after unit  
#32.  
Too many products  
Keep DMX and signal patch cables separated  
from power cables or black lights  
Interference from AC wires  
If you still experience problems after trying the above solutions, contact  
CHAUVET® Technical Support.  
MotionDrape™ LED User Manual (Rev. 05)  
 
Page 11 of 13  
In case you need to return a product or request support, follow the procedure below:  
Contact  
Procedure  
·
·
·
If you live in the U.S., contact CHAUVET® World Headquarters (see below).  
If you live in the UK or Ireland, contact CHAUVET® Europe Ltd.(see below).  
If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your  
distributor of record. Refer to our Web site for contact details of distributors outside  
the U.S., United Kingdom, or Ireland.  
World Headquarters  
CHAUVET®  
General Information  
Address:  
United Kingdom & Ireland  
CHAUVET® Europe Ltd.  
General Information  
Address:  
CHAUVET®  
Contact  
Information  
5200 NW 108th Avenue  
Sunrise, FL 33351  
(954) 929-1115  
Unit 1C  
Brookhill Road Industrial Estate  
Pinxton, Nottingham, UK  
NG16 6NT  
Voice:  
Fax:  
(954) 929-5560  
Toll free:  
(800) 762-1084  
Voice:  
Fax:  
+44 (0)1773 511115  
+44 (0)1773 511110  
Technical Support  
Technical Support  
Voice:  
Fax:  
(954) 929-1115 (Press 4)  
(954) 756-8015  
Email:  
Email:  
World Wide Web  
World Wide Web  
If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of  
record and follow their instructions on how to return CHAUVET® products to  
them. Visit our website for contact details.  
Call the corresponding CHAUVET® Tech Support office and request a Return  
Merchandise Authorization (RMA) number before shipping the product. Be prepared to  
provide the model number, serial number, and a brief description of the cause for the  
return.  
Returning  
Products to  
CHAUVET®  
You must send the merchandise prepaid, in its original box, and with its original packing  
and accessories. CHAUVET® will not issue call tags.  
Clearly label the package with the RMA number. CHAUVET® will refuse any product  
returned without an RMA number.  
DO NOT write the RMA number directly on the box. Instead, write it on a properly  
affixed label.  
Before sending the product, clearly write the following information on a piece of paper  
and place it inside the box:  
·
·
·
·
·
Your name  
Your address  
Your phone number  
The RMA number  
A brief description of the problem  
Be sure to pack the product properly. Any shipping damage resulting from inadequate  
packaging will be your responsibility. As a suggestion, proper UPS packing or double-  
boxing is always a safe method to use.  
CHAUVET® reserves the right to use its own discretion to repair or replace  
returned product(s).  
Page 12 of 13  
MotionDrape™ LED User Manual (Rev. 05)  
 
6. TECHNICAL SPECIFICATIONS  
Length (Drape)  
Width (Drape)  
Height (Drape)  
Weight (Drape)  
Dimensions and  
Weight  
9.8 ft (118 in)  
6.6 ft (78.7 in)  
2 m (2,000 m)  
0.6 in (15 mm)  
9.8 lbs (4.4 kg)  
3 m (3,000 mm)  
Length (Control Box) Width (Control Box) Height (Control Box)  
9.6 in (243 mm) 5.3 in (135 mm) 2 in (50 mm)  
Weight (Control Box)  
1.8 lbs (0.8 kg)  
Note: Dimensions in inches and feet rounded to the nearest decimal digit.  
Power Supply Type  
Range  
Voltage Selection  
Power  
Switching (internal)  
100~240 V, 50/60 Hz  
Auto-ranging  
Parameter  
Consumption  
Operating  
Fuse  
120 V, 60 Hz  
51 W  
230 V, 50 Hz  
54 W  
0.4 A  
0.2 A  
F 2 A, 250 V  
F 2 A, 250 V  
Power I/O  
US/Worldwide  
IEC  
UK/Europe  
IEC  
Power input connector  
Power output connector  
Power Cord plug  
Edison  
IEC  
Edison (US)  
Local plug  
Type  
Quantity  
Lifespan  
Light Source  
Thermal  
DMX  
LED  
176  
50,000 hours  
Maximum External Temp.  
Cooling System  
104° F (40° C)  
Convection  
I/O Connectors  
Connector Type  
Channel Range  
3-pin XLR  
Sockets  
8
Product Name  
Item Code  
Item Number  
Ordering  
MotionDrape™ LED  
15090388  
MOTIONDRAPELED  
MotionDrape™ LED User Manual (Rev. 05)  
 
Page 13 of 13  

Black Decker Oven TRO300 User Manual
Bostitch Staple Gun D61ADCSB User Manual
Breville Kitchen Grill SG620XL User Manual
Butler Coffeemaker 645 067 User Manual
Campbell Hausfeld Air Compressor FP260200 User Manual
Canon Film Camera EOS Elan II Body Only User Manual
Chamberlain Garage Door Opener 2565 1 2 HP User Manual
Chamberlain Universal Remote 84LM User Manual
Cisco Systems Network Card 350 User Manual
Cisco Systems Network Card RSP7000 User Manual