Casablanca Fan Company Outdoor Ceiling Fan 99087 User Manual

Decorative  
4-Light Fixture  
Installation Manual  
Models 99087, 99088, 99089, 99090, 99091  
Compatible with:  
2xxxx Types A - Z  
51000-58999 fan series  
59500-59999 fan series  
Select Casablanca Fans  
MA004-01 • 07/24/13  
 
1.888.830.1326  
WHICH ASSEMBLY METHOD WILL I USE?  
Choose one of the four images below that most closely resembles the switch  
housing on your fan; then follow the instructions under the image.  
Switch  
Housing  
Screw  
Switch  
Housing  
Cap  
Switch  
Housing  
Cap  
Cap  
Screw  
If your fan’s switch housing cap  
If your fan’s switch housing cap resembles  
this one, remove the whole switch  
resembles this one, remove the cap  
screws with a Phillips head screwdriver.  
Then follow the TYPE-A ASSEMBLY  
INSTRUCTIONS on pages 4-5.  
housing by removing the switch housing  
screws with a Phillips head screwdriver.  
Remove the two cap screws from the  
inside of the switch housing. Reinstall  
the switch housing. Tighten the switch  
housing screws. Then follow the TYPE-A  
ASSEMBLY INSTRUCTIONS on pages 4-5.  
Switch  
Housing  
Screw  
Switch  
Housing  
Plug  
Plug  
Button  
Screw  
Button  
If your fan’s switch housing cap  
resembles this one, remove the whole  
switch housing by removing the switch  
housing screws with a Phillips head  
screwdriver. Remove the plug button.  
Then follow the TYPE-B ASSEMBLY  
INSTRUCTIONS on pages 6-7.  
If your fan’s switch housing cap resembles  
this one, remove the whole switch  
housing by removing the switch housing  
screws with a Phillips head screwdriver.  
Remove the plug button using a standard  
screwdriver. Then follow the TYPE-C  
ASSEMBLY INSTRUCTIONS on pages 8-9.  
3
 
MA004-01 • 07/24/13  
1.888.830.1326  
TYPE-A ASSEMBLY INSTRUCTIONS  
1
2
Light Kit  
Screw  
Switch  
Housing  
Wire  
Connector  
Remove the pre-installed light kit screws  
and replace them with the longer light  
kit screws provided.  
If your fan does not have pin connectors on the  
wires coming from the switch housing, install  
the wiring harness provided. Using the provided  
wire connectors connect the white wire from the  
fan to the white wire from the wire harness and  
connect the black or blue wire from the fan to  
the black wire from the wire harness.  
3
4
Light Kit  
Screw  
Using the single pin connectors, connect  
the black or blue wire from the fan to the  
black wire from the light kit. Connect the  
white wire from the fan to the white wire  
from the light kit.  
Lift the light kit up to meet the lower  
switch housing. Align the light kit screws  
with the threaded holes in the lower  
switch housing. Tighten screws securely.  
Do not allow the light kit to hang  
only by the wire connections!  
4
 
MA004-01 • 07/24/13  
1.888.830.1326  
TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED)  
5
6
Socket  
Shade  
(sold separately)  
Socket  
Ring  
Socket  
Ring Tool  
Installing the shades (sold separately)-  
Remove the socket rings from the  
sockets. Install each shade onto a socket.  
Install the socket rings onto the sockets  
by turning them clockwise using the  
socket ring tool.  
Installing the bulb - Install a bulb into each  
socket. When necessary, replace bulbs with  
bulbs of same type and wattage.  
7
8
ON  
Installing the pull chain pendant -  
Attach the pull chain pendant to the  
end of the short chains coming from the  
switch housing and the light kit.  
Turn on power. Your  
installation is complete!  
5
 
MA004-01 • 07/24/13  
1.888.830.1326  
TYPE-B ASSEMBLY INSTRUCTIONS  
1
2
Wire  
Connector  
Switch  
Housing  
If your fan does not have pin connectors  
on the wires coming from the switch  
housing, install the wiring harness  
provided. Using the provided wire  
connectors connect the white wire from  
the fan to the white wire from the wire  
harness and connect the black or blue  
wire from the fan to the black wire from  
the wire harness.  
Feed the wires through the center hole in  
the switch housing, the washer, and the nut.  
Push the center hole in the gasket over the  
threaded rod of the light kit. Then install the  
switch housing by twisting clockwise onto  
the threaded rod. Install the washer and nut  
onto threaded rod and tighten securely.  
3
4
Switch  
Housing  
Screw  
Using the single pin connectors, connect  
the black or blue wire from the fan to the  
black wire from the light kit. Connect the  
white wire from the fan to the white wire  
from the light kit.  
Lift the light kit assembly up so that the  
screw holes in the lower switch housing  
line up with the holes in the upper switch  
housing. Install the switch housing  
screws and tighten securely.  
Do not allow the light kit to hang  
only by the wire connections!  
6
 
MA004-01 • 07/24/13  
1.888.830.1326  
TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED)  
5
6
Socket  
Shade  
(sold separately)  
Socket  
Ring  
Socket  
Ring Tool  
Installing the shades (sold separately)-  
Remove the socket rings from the  
sockets. Install each shade onto a socket.  
Install the socket rings onto the sockets  
by turning them clockwise using the  
socket ring tool.  
Installing the bulb - Install a bulb into each  
socket. When necessary, replace bulbs with  
bulbs of same type and wattage.  
7
8
ON  
Installing the pull chain pendant -  
Attach the pull chain pendant to the  
end of the short chains coming from the  
switch housing and the light kit.  
Turn on power. Your  
installation is complete!  
7
 
MA004-01 • 07/24/13  
1.888.830.1326  
TYPE-C ASSEMBLY INSTRUCTIONS  
1
2
Washer  
and Nut  
Threaded  
Rod  
Switch  
Housing  
Wire  
Connector  
If your fan does not have pin connectors  
on the wires coming from the switch  
housing, install the wiring harness  
provided. Using the provided wire  
connectors connect the white wire from  
the fan to the white wire from the wire  
harness and connect the black or blue  
wire from the fan to the black wire from  
the wire harness.  
Feed the wires through the switch  
housing cap, washer, and nut. Then  
install the switch housing cap by twisting  
clockwise onto the threaded rod, making  
sure the gasket stays in line with the top  
of the light kit. Install the washer and nut  
onto threaded rod and tighten securely.  
3
4
Upper  
Switch  
Housing  
Using the single pin connectors, connect  
the black or blue wire from the fan to the  
black wire from the light kit. Connect the  
white wire from the fan to the white wire  
from the light kit.  
Lift the light kit assembly up so that the  
screw holes in the lower switch housing  
line up with the holes in the upper switch  
housing. Install the switch housing  
screws and tighten securely.  
Do not allow the light kit to hang  
only by the wire connections!  
8
 
MA004-01 • 07/24/13  
1.888.830.1326  
TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED)  
5
6
Socket  
Shade  
(sold separately)  
Socket  
Ring  
Socket  
Ring Tool  
Installing the shades (sold separately)-  
Remove the socket rings from the  
sockets. Install each shade onto a socket.  
Install the socket rings onto the sockets  
by turning them clockwise using the  
socket ring tool.  
Installing the bulb - Install a bulb into each  
socket. When necessary, replace bulbs with  
bulbs of same type and wattage.  
7
8
ON  
Installing the pull chain pendant -  
Attach the pull chain pendant to the  
end of the short chains coming from the  
switch housing and the light kit.  
Turn on power. Your  
installation is complete!  
9
 
MA004-01 • 07/24/13  
1.888.830.1326  
TROUBLESHOOTING  
Lights don’t come on.  
Make sure that the bulbs are properly installed.  
Make sure power switch is on.  
• Pull the pull chain to make sure it is on.  
Check the circuit breaker to ensure the power is turned on.  
Check the pin connections in the light kit.  
Refer to the fan manual for locating the fan’s wiring. Verify that the light and power  
wires are correctly connected to the ceiling and the light kit.  
ONE YEAR WARRANTY  
This product is warranted to the original purchaser by Casablanca Fan Company/  
Hunter Fan Company against defects in material and workmanship for one (1)  
year from date of purchase. During the warranty period, we will repair or, at our  
option, replace a defective product at no charge. For information on how to obtain  
service, contact the Casablanca/Hunter Service Department by calling our toll-  
free number at 888-830-1326. Damage to the product caused by mishandling,  
improper installation or modification is not covered by this warranty. This warranty  
is given in lieu of all other warranties expressed or implied. Some states do not allow  
limitations of time on an implied warranty, therefore the above limitations may not  
apply in every case. This warranty states specific legal rights which may vary from  
state to state.  
If you have problems installing or operating your light kit, do not return this product  
to the dealer. Call our Consumer Affairs Hotline.  
888-830-1326  
Monday through Friday  
8:00 am to 4:30 pm Central  
10  
 
MA004-01 • 07/24/13  

Black Decker Cordless Drill BD14PS User Manual
Black Decker Griddle GR100 User Manual
Bosch Appliances Welding System VG4 100 User Manual
Bose TV Video Accessories Lifestyle R VS 2 User Manual
Breville Toaster BTA340 User Manual
Briggs Stratton Pressure Washer 020244 0 User Manual
Cadillac Mobility Scooter CTS V Series User Manual
Carson Automobile Alarm SA 360 User Manual
Chief Manufacturing Indoor Furnishings FHP 110 User Manual
Cisco Systems IP Phone 6921 User Manual